About this role
**The role will be based out of Corpus Christi, TX, work in the Permian, and travel across the area!
Job Summary
We are seeking a highly skilled Field Service Technician to support the installation, commissioning, maintenance, and troubleshooting of oil & gas measurement and automation systems, including LACT units, meter skids, NGL skids, and gas meter runs.
This role requires a strong foundation in electrical, instrumentation, and mechanical systems, along with the ability to diagnose complex field issues, improve system reliability, and deliver high-quality service to customers in demanding field environments.
The ideal candidate thrives in a fast-paced, hands-on environment and is committed to safety, precision measurement, and continuous improvement.
Primary Responsibilities:
Measurement Systems & Equipment
Install, commission, and start up:
-
ACT (Lease Automatic Custody Transfer) units
-
Crude oil, produced water, and NGL meter skids
-
Gas meter runs (orifice, ultrasonic, Coriolis, thermal mass)
-
Perform meter proving, calibration, and system validation in accordance with API and AGA standards
-
Troubleshoot and repair:
-
Flow meters (Coriolis, ultrasonic, turbine, PD)
-
Control valves, regulators, and back pressure valves
-
Pumps, motors, and mechanical components
-
BS&W equipment, sampling systems, and analyzers Electrical, Controls & Instrumentation
-
Install, commission, and troubleshoot:
-
Electrical systems (up to 480V), MCCs, and control panels
-
PLCs, RTUs, flow computers, and HMI systems
-
VFDs, transmitters (pressure, temperature, flow, level), and I/O systems Diagnose faults using:
-
Multimeters, megohmmeters, and diagnostic tools
-
Electrical schematics, loop diagrams, and P&IDs
-
Ensure proper grounding, bonding, and compliance with electrical and safety standards Field Service & Customer Support
-
Respond to scheduled and emergency service calls across the Permian Basin
-
Execute work safely using LOTO, JSAs, permits, and energized work procedures
-
Interface directly with customers, providing technical expertise and professional service
-
Generate detailed service reports including: o Root cause analysis
o Failure modes
o Corrective actions and recommendations
Reliability & Continuous Improvement
- Perform preventative and predictive maintenance to reduce downtime
- Identify recurring failures and drive root cause solution Contribute to:
o Standard work development
o Troubleshooting guides and checklists
o First-time fix rate improvements
Support a Lean, safety-first culture focused on:
o Reducing variation
o Improving uptime
o Enhancing service quality
Experience
-
5+ years of field service experience in oil & gas, measurement, or industrial environments Strong knowledge of:
-
o Industrial electrical systems (480V and below)
-
o Measurement systems and instrumentation
Ability to read and interpret:
-
P&IDs
-
Electrical schematics and loop diagrams
-
Experience working independently in remote field locations
-
Valid driver’s license required, with the ability to maintain a clean and safe driving record.
-
Preferred Qualifications
-
Experience with LACT units, meter skids, or gas measurement systems
-
Flow computer experience (ABB, Emerson ROC & FB3000, OMNI, WAGO, etc.)
-
PLC/HMI experience (Allen-Bradley, Siemens, IDEC, Red Lion, Beijer, etc.)
-
VFD experience (ABB, Danfoss, Rockwell, Schneider, LS, Benshaw, etc.)
-
Familiarity with API and AGA standards
-
Certifications: OSHA 10/30, H2S, Safeland/PEC, Arc Flash, TWIC
-
Lean / Six Sigma or reliability experience
-
Education and Training
-
High School Diploma or GED required
-
Technical or vocational training in Electrical, Instrumentation, or Industrial Maintenance preferred
-
Equivalent field experience or 5–10 years in a similar technical role accepted.
-
Work Environment & Requirements
-
Frequent travel across the Permian Basin, STX, SE NM. (up to 90-95%)
-
Work outdoors in extreme conditions (heat, cold, dust, wind)
-
Regularly lift and/or move up to 25 lbs. (12 kg); frequently up to 50 lbs. (23 kg); and occasionally up to 100 lbs. (45 kg). (Above 100 lbs. help will be required)
-
Climb ladders, structures, and equipment Willingness to work:
-
o Overtime
-
o On-call rotations
-
o Nights, weekends, and holidays as needed
-
Compliance with all company policies, including Drug & Alcohol policy.
-
Ability to work safely and collaboratively.
-
Must be authorized to work in the United States.
-
What We Offer**
-
Competitive hourly pay + overtime
-
Company vehicle, tools, and test equipment
-
Per diem (if applicable)
-
Medical, dental, vision, and 401(k)
-
Ongoing technical and safety training
-
A strong culture focused on safety, measurement accuracy, and continuous improvement
-
Strike is an equal opportunity employer.